Fasteners & Hardware

Disc brake pad adjuster tab washer

Disc brake pad adjuster tab washer. For all Lambrettas equipped with original disc style brakes...

$2.00

Disc locating pin

Disc locating pin, for replacing the worn out pins in original Lambretta front disc brake. A tr..

$9.00

End cap hardware kit: Series 3

Hardware that goes through all the endcaps of a Series 3. Kit contains: 6 m4 x 20 screws ..

$10.00

Engine circlip kit

This handy bagged kit contains the correct circlips you need to overhaul a Lambretta engine. It does..

$12.00

Exhaust nut: 7mm, Brass

This special nut is suitable for use on the studs that secure a Lambretta exhaust...

$2.00

Flywheel and cylinder shroud hardware kit: Series 1-3

To install both the cylinder and flywheel/fan shroud on Series 1-3, DL/GP. Consists of: 7 m5 ..

$5.00

Flywheel and head cowl HEX kit

This handy kit contains the correct number of hex set screws and washers to fit your head and flywhe..

$4.00

Front axle half nut washer and side panel lever washer

Front axle half nut washer. This washer goes between the half nut and the back plate on drum type fr..

$0.45

Front axle locating washer, stainless

This washer sits in your fork link to hold your axle (and hub!) in place, so it is important it is..

$5.00

Front axle locating washer, zinc

This washer sits in your fork link to hold your axle (and hub!) in place, so it is important it is..

$2.00

Front floor rails hardware kit: Series 3

For installing the 4 front alloy channels on Series 3 and DL. Consists of: 6 m4 x 10 screws..

$12.00

Front mudguard hardware kit: Series 3

This kit includes: 2 m5 x 20 screws for the bottom (under aluminum channel) 2 m5 nuts for ab..

$5.00

Gear selector wishbone screw

This fastener can specifically be used for the shifter wishbone, eliminating the need for a 9mm sock..

$0.45

Grease nipple: M6 x 1.00 11 mm wrench

Grease nipple: M6 x 1.00 11 mm wrench Used on some front hub backplates, fork links, fork link bolt..

$2.00

Grease nipple: M8 x 1.25 11 mm wrench

Grease nipple: M8 x 1.25 11 mm wrench Used on the front hub of some Lambrettas. ..

$2.00

Grease nipple: M8 x 1.25 14 mm wrench TECALEMIT D/LD

Grease nipple: M8 x 1.25 14 mm wrench TECALEMIT D/LD..

$5.00

Handlebar light switch housing screw

Used to secure the Lambretta light switch housing to the headset. You need two per scooter. M6x12..

$0.45

Handlebar light switch screws: Series 1-3, GP/DL, Serveta

Kit for securing the light switch to the handlebar. Consists of: 2 m3 x 25 screws ..

$2.00

Headlight rim hardware kit: Series 1, Series 2 Li/TV, Series 3 Li

Headlight rim hardware kit: Series 1, Series 2 Li/TV, Series 3 Li. Kit consisting of: 4 m4 x 1..

$2.00

Headlight rim hardware kit: Series 3 LiS/TV/SX

Kit for securing the headlight rim on all Series 3 LiS, TV and SX models. Kit consists of: 4 ..

$1.00